THE ORIGINAL Rose/Jenkins Bell Tools and BIG BOY Swede (1.3 x 1.7) Combo Kit

$429.95

By the kit and save!

Designed to have the newest JW tools all in one kit. This kit includes:
– The largest Swede Die with tall brass pushers and Ross pusher 1.3″ x 1.7″
– A Rose/Jenkins Bell Tool/Riser/Ring Bearer with a viewing window.
– All four sizes of dapping punches. Sizes 1.5″, 1.25″, 1.0″ and .75″
– A Bell Tool/Riser/Ring Bearer for full extrusion of the ring out of the bottom of the Swede dies
– A wood holder to organize all your tools.
– One roll of pipe tape.
– One Jason’s Works sticker

Description

Buy the complete set and save if purchased separately.

NOTE: This kit with the Gamut Kit are all the tools available from Jason’s Works. Shipping limitations require separate orders and packages for this kit and the Gamut.

For additional information on how to make bells and one of the persons that inspired these tools, visit Skyler Jenkins video here:

NOTE: Stay tuned for a Jason’s Works (JW) Bell video using these tools.

For additional information of the Ross pushers and tall brass in use you can view a training video here:

Designed to have the newest JW tools all in one kit.
– The largest Swede Die with tall brass pushers and Ross pusher 1.3″ x 1.7″
– A Rose/Jenkins Bell Tool/Riser/Ring Bearer with a viewing window.
– All four sizes of dapping punches. Sizes 1.5″, 1.25″, 1.0″ and .75″
– A Bell Tool/Riser/Ring Bearer for full extrusion of the ring out of the bottom of the Swede dies
– A wood holder to organize all your tools.
– One roll of pipe tape.
– One Jason’s Works sticker
.
REGARDING THE BELL TOOLS:
The first coin bell was created by Edward Rose. His work can be found on Facebook in the private group Coin Ring Crafters. He has helped inspire these tools as well as Skyler Jenkins, “Change You Can Wear”. Watch Skyler’s first bell video here:

Simply place a coin in a Jason’s Works 17 degree die that fits, it must sit inside on the bevel of the die. It is ok if it is slightly lower than the top. Place the Bell Tool on top of the die as seen in the pictures above and press a dapping punch of the size you want down on to the coin or other no ferrous disc. I like to anneal the coin and use a 1 ton arbor press. A hydraulic press can be used but be sure your ram is straight and true and use the press carefully. Remember, “power tools make power mistakes”.

The bell tool is designed to sit on top of different sized 17 degree dies for dapping non ferrous coins and discs. There is a viewing window so you can watch the coin during the doming process. The Bell Tool can also double as a riser for your other 17 degree, 25 degree folding dies and your Swedish dies as well. You can extrude out of the bottom of the swede die and into the Bell Tool Riser. (See the pictures above).

What size dap do I need? This depends on you. What coins will you be using and what shape do you like? I like to use multiple sized Bell Daps to get the shape I desire and finish in a Swede die to get a 90 degree shoulder on the cap of the bell. I like to use the smallest dapping punch (.75″) from dimes to half dollars to get them started. The next size up for the next sized coins. Larger coins make larger bells. Remember the JW saying, “If it fits, It’ll work”.

REGAURDING THE BIG BOY SWEDE TOOLS:
The BIG BOY Swede Die at sizes 1.3 x 1.7 comes with it’s own tall brass plungers and Ross Pusher.

*NOTE: these taller bronze plungers are specially designed to bottom out when the plunger is flush with it’s corresponding die (see pictures above). This removes the chance of damaging the plungers by over pressing especially when using a hydraulic press.

It’s o.k. for the brass plungers to have small dings and scratches when they become well used. If need be, you can always lap the surfaces using a piece of 200 grit sand paper.

*NOTE: Remember the 5 most important steps in the Swedish Wrap method.
1. Anneal a lot. Preferably once for every plunger distance when working with silver. Up to two with brass. Better to anneal too often than not enough.
2. Use lots of pipe tape, re-wrap after each press/anneal. Better to use too much than too little. I wrap up to 30 times for a half dollar and 40 times for a dollar if I’m using the thin tape. It depends on the thickness of the tape and how tough the coin is. Luckily it’s cheap. Rolls can be found for well under a dollar at stores or online.
3. It is better to press the reed side. Prior to pressing, make sure the plunger completely covers the reed side of the coin. If it does not, use a 17 or 25 degree die to fold in the reed side until the plunger covers the reed side.
4. Do not over-press the plungers when using a hydraulic press or large arbor press. Know where each plunger bottoms out on the dies.
5. Feel free to experiment with different ideas and have fun!

The Ross Push Follower designed for Jason’s Works BIG BOY Swedish Die.

Conceived by Sam “Ross” Scafferi with Ross Coin Rings, the push followers have been slightly modified from his original design to efficiently press rings down and through Jason’s Works Swedish Wrap Dies (The coin ring technique called the Swedish Wrap, created by Mikael Möller from Sweden). Sam contacted me with his idea and wanted to see if this could be presented to the coin ring community to help with using the Swedish Wrap technique. With Sam’s prototype and much help from many people, the Ross Push Follower is now available. These are designed for light to medium duty. You can fully press and extrude a silver quarter, silver half dollar, and silver dollar through their respective Swede die with only one anneal.

*NOTE* The bronze plungers are still the best for heavy duty pushing.

How to use the Ross Push Follower:
1. Fold and reduce the coin ring as needed to fit into a Swedish die.
2. Anneal and wrap the ring with pipe tape.
3. Lube the inside of the die with coconut oil (Thank you Adam McKinney for that tip!)
4. Press your wrapped coin, reed side down, into a 25 degree die. This will cut the tape around the edge of the reed. (See picture above) This helps to keep the pusher from
slipping into the ring and damaging the pusher.
5. Insert the coin ring into the appropriate Swede die reed side up (see picture above).
6 Press using an arbor press or similar press and rotate the Pusher between short presses. This reduces the likelihood of deforming the ring (see picture above).
7. To have a perfectly straight wall, flip the ring over to the reed side down just before you reach your target size. Reduce to your target size with the reed side down.
8. To have a more rounded ring (fat tire or synclastic) remove the ring a few sizes above your target size and finish in a 25 degree reduction die.
9. Use the witness lines for repeatable sizing of your rings.

Tips and tricks:
1. Do not over press. These pushers are designed for light to medium duty. The first sign of failure is when the leg or post of the pusher begins to bend. When high pressures
are needed, the bronze pushers are best to use.
2. If you do over press and damage the pusher, it will most likely chip the edge of the pusher. This can be repaired by compressing the pusher’s legs with a zip tie (see above
picture) and sanding, filing, grinding the face flat while compressed. (Thank you, Skyler Jenkins, for this tip!). These are considered consumable but with proper use and maintenance, they can last a life time.
3. If the pusher begins to have a “memory” of a taper. You can insert the 1/4″ mandrel (see picture above) to regain the original straight shape. Leave the mandrel in overnight for best results.

For additional information of the Ross pushers and tall brass in use you can view a training video here:

Stay tuned for an updated training manual:
https://www.etsy.com/listing/170473451/new-swedish-wrap-technique-edition-42?ref=shop_home_active_8

*A special thank you to Edward Rose, Skyler Jenkins, Mikael Möller, Robert Gibb (BFG Coin RIngs), Bob, Russ, Troy, Mike Henry, Adam McKinney, Skyler Jenkins (Coin Rings by the Mint), Rocky Workman, Joshua Janes and countless others on Coin Ring Crafters on Facebook. You all made this possible! 🙂

*COINS, RINGS AND BELL NOT INCLUDED*

Title

Go to Top