THE ORIGINAL Swede Die and Ross Push Follower Kit of your choice

$94.90

The Ross Push Follower designed for Jason’s Works Swedish Dies. Choose the size you need for your Swedish Die, The Small is for the .6 x .9 Quarter Swede die, Medium is for the .8 x 1.1 half dollar Swede die, and the Large is for the 1.0 x 1.4 Dollar Swede Die.

Stay tuned for an in depth video showing these at work.

Description

Choose a kit of your choice.

The Ross Push Follower designed for Jason’s Works Swedish Dies. Choose the size you need for your Swedish Die, The Small is for the .6 x .9 Quarter/Dime Swede die, Medium is for the .8 x 1.1 half dollar Swede die, and the Large is for the 1.0 x 1.4 Dollar Swede Die

NEW! Urethane plugs designed to help support the legs and keep them from slipping in the ring. Thank you John Harkai for this idea and Mike Beaclaire finding the plugs. The plugs are blue or red depending on the size of the Ross pusher you order. Please leave them inside the pusher. Feel free to adjust them forward or backward to give you different amounts of support as needed.

Video showing the new inserts:

Conceived by Sam “Ross” Scafferi with Ross Coin Rings, the push followers have been slightly modified from his original design to efficiently press rings down and through Jason’s Works Swedish Wrap Dies (The coin ring technique called the Swedish Wrap, created by Mikael Möller from Sweden). Sam contacted me with his idea and wanted to see if this could be presented to the coin ring community to help with using the Swedish Wrap technique. With Sam’s prototype and much help from many people, the Ross Push Follower is now available. These are designed for light to medium duty. You can fully press and extrude a silver quarter, silver half dollar, and silver dollar through their respective Swede die with only one anneal.

*NOTE* The bronze plungers are still the best for heavy duty pushing.

How to use the Ross Push Follower:
1. Fold and reduce the coin ring as needed to fit into a Swedish die.
2. Anneal and wrap the ring with pipe tape.
3. Lube the inside of the die with coconut oil (Thank you Adam McKinney for that tip!)
4. Press your wrapped coin, reed side down, into a 25 degree die. This will cut the tape around the edge of the reed. (See picture above) This helps to keep the pusher from
slipping into the ring and damaging the pusher.
5. Insert the coin ring into the appropriate Swede die reed side up (see picture above).
6 Press using an arbor press or similar press and rotate the Pusher between short presses. This reduces the likelihood of deforming the ring (see picture above).
7. To have a perfectly straight wall, flip the ring over to the reed side down just before you reach your target size. Reduce to your target size with the reed side down.
8. To have a more rounded ring (fat tire or synclastic) remove the ring a few sizes above your target size and finish in a 25 degree reduction die.
9. Use the witness lines for repeatable sizing of your rings.

Tips and tricks:
1. Do not over press. These pushers are designed for light to medium duty. The first sign of failure is when the leg or post of the pusher begins to bend. When high pressures
are needed, the bronze pushers are best to use.
2. If you do over press and damage the pusher, it will most likely chip the edge of the pusher. This can be repaired by compressing the pusher’s legs with a zip tie (see above
picture) and sanding, filing, grinding the face flat while compressed. (Thank you Skyler Jenkins for this tip!). These are considered consumable but with proper use and maintenance, they can last a life time.
3. If the pusher begins to have a “memory” of a taper. You can insert the 1/4″ mandrel (see picture above) to regain the original straight shape. Leave the mandrel in overnight for
best results.

View an in depth video showing these at work:

The smaller sized rings can be incorporated into bracelets, necklaces, pendants, earrings, even ear gauges!

*A special thank you to Sam ‘Ross” Scafferi, Bob, Russ, Troy, Adam McKinney, Skyler Jenkins (Coin Rings by the Mint), Rocky Workman, Joshua Janes and countless others on Coin Ring Crafters on Facebook. You all made this possible! 🙂

Ross Coin Rings on Etsy:
https://www.etsy.com/shop/RossCoinRings

*COINS AND RINGS NOT INCLUDED*

Title

Go to Top