-
Peace Silver Dollar Coin Ring: Custom coin ring from Jason's Works made with the highest quality coin ring making tools available in the USA. This is an example of the custom made Peace silver dollar coin ring that you would receive. These were minted from 1921 to 1928 and again in 1934 and 1935. Choose the year and size you would like. These are BIG rings, heavy and thick. They make great thumb rings. Some coins will have more wear than others, I will pick the best coins I have first. *NOTE: The smaller sizes will be a very thick ring. -
Platinum Coin Ring: Custom coin ring from Jason's Works made with the highest quality coin ring making tools available in the USA. A custom made one troy ounce .999 platinum Isle of Man Angel coin ring. This coin has a bust of the Queen on the obverse and the Angel Michael slaying a dragon on the reverse. This is truly a one of a kind coin ring. -
2014 Silver Isle of Man Angel Coin Ring from Jason's Works made with the highest quality coin ring making tools available in the USA. The newest 2016 design has a few changes from the previous years. The words "AG. 999. ! Ounce" are recessed rather than raised and the angel design is slightly smaller. I have created a slightly larger band width to capture the same design of the older coins. A custom made one troy ounce .999 silver Isle of Man Angel coin ring. This coin has a bust of the Queen on the obverse and the Angel Michael slaying a dragon on the reverse. This is truly a one of a kind coin ring. This is a very large and thick coin ring. *NOTE: The smaller sizes will be a very thick ring. -
Out of stock
Silver Coin Ring (Colombian Exposition). This is a picture of an example of the coin ring you will receive. This particular ring is size 11. Choose your size and year that you would like. The Columbian Exposition half dollar is a commemorative coin minted to raise funds for the World's Columbian Exposition held in 1893 in Chicago and to commemorate the quadricentennial of the first voyage of Christopher Columbus to the Americas. At this World's Fair, Nikola Tesla first introduced electricity to the world. This ring is beautiful! Especially for a coin that is 120 years old. The price is set higher partly because of a small numismatic value Note that with normal wear, the patina will wear off to a shiny silver. Some coins will have more wear than others, I will pick the best coins I have first. *NOTE: The smaller sizes will be a very thick ring. -
2016 Silver Isle of Man Angel Coin Ring -
One olive pick made from 18k gold. Very very fancy! These are the only gold olive picks that I know of in the world. Approximately 5 inches in length. There is an 18k gold hallmark located on the end. Approximately 1/4 troy ounce of 18k gold! -
Have you been looking for the coolest bottle opener in the world?...well look no further! These are truly a one of a kind solid sterling silver railroad spike bottle opener. "Why?" you may ask.....why not! :) I took my discarded silver pieces from silver coin rings and alloyed pure silver with them to produce a 92.5% + sterling silver sand cast railroad spike. I then hand forged the sterling silver railroad spike into a one of a kind bottle opener with a Rubik cube twist handle. There is certainly no other bottle opener like this in the world (well....I've made three so far). I decided to leave the forge marks as it left my anvil. It shows the authenticity of the handmade quality of the piece and offers an interesting juxtaposition of the elegance of silver and the roughness of a railroad spike. Weighing in at a hefty 12.9 troy ounces, it is a substantial amount of sterling silver. Hallmarked with my makers mark and purity, you can buy with confidence. As always, my work is 100% guaranteed. Each one is custom made so there may be slight differences in your custom made bottle opener. Thanks for looking and be sure to look at my other items in my etsy store. Thanks! Jason -
A custom made beautiful swirly bracelet. This photo is an example of the bracelet you will receive. Choose the size you would like and material. These bracelets are 5/8 inch wide and weigh approximately one troy ounce. -
Out of stock
The Classic self centering coin ring punch and die set made in the U.S.A. Get that perfectly centered hole in your U.S. quarter, half dollar, and Morgan coins to make double sided coin rings. Spacers are required in this punch to center coins in the punch. (Be sure to check out the new Auto punch that does not require spacers) Punch and die sizes included are: 3/8" 7/16" 1/2" -
Store your Swedish Wrap tools in a custom made holder. Made from high quality red oak, this tool holder will hold your two Swedish dies and 5 bronze plungers. *Tools not included* -
A custom made Ben Franklin silver coin ring. These were minted from 1948 to 1963. Choose the year and size you would like. Some coins will have more wear than others, I will pick the best coins I have first. *NOTE: The smaller sizes will be a very thick ring. -
A custom made one troy ounce .9995 platinum American Eagle coin ring. This coin has Lady Liberty on the obverse and an Eagle on the reverse. Current years are available as well as 1/2 troy ounce and 1/4 troy ounce coins. Your ring size may determine what size coin you will need. Smaller coins/rings will be less in price. Please inquire if interested. Pictured is a 1 troy once coin ring at size 8.5. -
United States Silver Eagle Dollar Coin Ring from Jason's Works made with the highest quality coin ring making tools available in the USA. This is an example of the custom made Silver Eagle dollar coin ring that you would receive. Choose the size you would like. These are BIG rings, heavy, thick and soft due to being pure .999 silver. They make great thumb rings. Some coins will have more wear than others, I will pick the best coins I have first. -
This listing is for one hand forged sterling silver cocktail stirrer spoon with a forked end. The spoon holds approximately 1 teaspoon for measuring. The fork is very effective at grabbing and holding on to olives and those slippery cherries. Very fancy and no two are alike. Approximately 12 inches in length and weighing at approximately a hefty 1.5 Troy ounces of solid sterling silver. There is a "Sterling" hallmark and "J.A. Stinchfield" makers mark located on the spoon. Note: This is not the exact one you will receive. -
This listing is for one olive pick made from Sterling Silver. Very fancy! Approximately 5 inches in length. Note: his is not the exact one you will receive. There is a Sterling Silver and USA hallmark located on the end. Approximately 1/3 troy ounce of silver! -
Well, I'm no model but here are some shots of the t-shirt by popular demand. A black t-shirt with Jason's Works logo (drawn by me :) on the front, back, and a banner on the right sleeve. Pick your out your size at the top right. These Hanes Beefy-T's are 100% preshrunk cotton. -
Enjoy a hot cup of coffee or tea while making your coin rings! A classic black mug with Jason's Works logo (drawn by me :) ) on one side. An odd ball size for shipping with USPS flat rate so it is best to combine this mug with other items if possible. -
By popular demand, now you can store your coin ring tools and organize your work space. Made from high quality red oak, this tool holder will hold your Auto coin ring punch, six punches, penny and dime 1/4" hole mandrel, all four stabilizing universal cones and spacer, stabilizing universal cone mandrel and the NEW starter cone. *A recent review: "Excellent tray holds my punch body, all 5 size punches/dies, all 4 folding cones, folding cone spacer, stainless steel starter cone, and the small mandrel for making dimes/pennies. Finished with what appears to be a light varnish to protect the surface while retaining the wood's natural color. The inside of each recess is bare. I might add a little clear coat or varnish in them, but I'm undecided on that as of now. If they were varnished I think the tools may clank around in each hole so maybe bare wood is the better option. I also got the Folding Die Holder which has the same finish as this. Excellent quality wood with no imperfections or cracks!" Angus MacGyver on Apr 25, 2016 5 out of 5 stars *Tools not included* -
(NOTE: The Auto punches will not work in the classic self centering punch) (NOTE: Punch housing and punch not included) Choose the die size you would like. For multiple dies, please add multiple orders to your cart. The hole size has a direct effect on the band width of the finished ring. The bigger the hole, the smaller the band width for a specific coin. I believe the largest possible ring sizes for coins look best with a wider bands as the material stretches thinner and the smallest possible ring sizes for coins look best with larger holes as the material compresses and elongates. -
Out of stock
The Classic self centering coin ring punch and die set made in the U.S.A. Get that perfectly centered hole in your coins to make double sided coin rings. Spacers are required in this punch to center coins in the punch. (Be sure to check out the new Auto punch that does not require spacers) One Spacer and one Punch and die size of your choice as well as spacer -
By popular demand, now you can store your coin ring tools and organize your work space. Made from high quality red oak, this tool holder will hold your classic self centering coin ring punch, five punches, penny and dime 1/4" hole mandrel, all four stabilizing universal cones and spacer, stabilizing universal cone mandrel and the NEW starter cone. *A recent review: "Excellent tray holds my punch body, all 5 size punches/dies, all 4 folding cones, folding cone spacer, stainless steel starter cone, and the small mandrel for making dimes/pennies. Finished with what appears to be a light varnish to protect the surface while retaining the wood's natural color. The inside of each recess is bare. I might add a little clear coat or varnish in them, but I'm undecided on that as of now. If they were varnished I think the tools may clank around in each hole so maybe bare wood is the better option. I also got the Folding Die Holder which has the same finish as this. Excellent quality wood with no imperfections or cracks!" Angus MacGyver on Apr 25, 2016 5 out of 5 stars *Tools not included* -
Get this die to upgrade your current 5/8 inch punch set for your Jason's Works self centering coin ring punch. I like to use this punch size for Morgan dollar and Silver Eagle dollar sized coins. The die is hardened tool steel, hand lapped to be ultra smooth, and zinc plated to resist rust. This new design allows for the plug to fall through the die immediately. Remove the plug from the housing by simply turning the housing over. -
Out of stock
Purchase in a set and save. Newfoundland ring blanks designed specifically to be made into rings. Designed from the Newfoundland 50 cent pieces, this ring blank has a 1/2" hole and is ready to be folded and made into a ring! Similar is size and shape of a United States half dollar, these make great rings for both men and women. Best if purchased with other items to combine shipping. NOTE: These are made from brass so it will discolor your finger NOTE: Ring not included -
A custom made walking liberty silver coin ring. These were minted from 1916 to 1947 excluding 1922, '24, '25, '26, '30, '31 and 1932. Choose the year and size you would like. Some coins will have more wear than others, I will pick the best coins I have first. *NOTE: The smaller sizes will be a very thick ring. -
Buy USA coin rings online: Morgan Silver Dollar Coin Ring from Jason's Works made with the highest quality coin ring making tools available in the USA. This is an example of the custom made Morgan silver dollar coin ring that you would receive. These were minted from 1878 to 1904 and again in 1921. Choose the year of either pre or post 1900. If you have a specific year in mind, Let me know and I'll see if I have one. Also, let me know if you would like "tails" showing on the band in the comments section of your order. These are BIG rings, heavy and thick. They make great thumb rings. Some coins will have more wear than others, I will pick the best coins I have first. *NOTE: The smaller sizes will be a very thick ring. -
By popular demand, now you can store your Jason's Works folding and stretching tools to organize your workspace. Made from high-quality red oak, this tool holder will hold up to 11 reduction dies for easy access while making your coin rings, including the 1.7 x 1.8 @17 degree BIG boy die. *Tools not included* -
Now punch up to a 1/4"" hole in your pennies, dimes, and other small coins! This is a custom made 1/4 inch punch, die, penny spacer, dime spacer, and a top plate with a 3/8"" hole to press and hold down the coin. The punch and die are machined from tool steel and hardened to approximately 52 rockwell. Proudly made in the U.S.A. -
A single brass plunger to replace a lost or damaged (beyond repair) plunger. These are the best quality available being hardened bronze, engraved witness lines and being hand lapped. These are not just mass produced but rather each one is finished by hand by a skilled craftsman or woman here is the USA. I f you need multiple plungers, you can add them separately to your cart. For additional information you can view a training video here: https://www.youtube.com/watch?v=W7gZxUKNr1g And also get detailed step by step instructions from my training manual available here: https://jasons.works/product/coin-ring-tools-training-manual/ -
Out of stock
By popular demand, now you can store your folding/reduction dies and coin ring anvil to organize your work space. Made from high quality red oak, this tool holder will hold up to 8 reduction dies for easy access while making your coin rings. * A recent review: "Excellent tray holds all my folding dies! Finished with what appears to be a light varnish to protect the surface while retaining the wood's natural color. The inside of each recess is bare. I might add a little clear coat or varnish in them, but I'm undecided on that as of now. If they were varnished I think the dies may clank around in each hole so maybe bare wood is the better option. I also got the Coin Ring Tool Holder which has the same finish as this. Excellent quality wood with no imperfections or cracks!" Angus MacGyver on Apr 25, 2016 5 out of 5 stars *Tools not included* -
By popular demand, now you can store your coin ring tools and organize your work space. Made from high-quality red oak, this tool holder will hold your Auto coin ring punch housing and all 9 punches and dies. *Tools not included* -
Store your Swedish Wrap tools in a custom made holder. Made from high quality red oak, this tool holder will hold your two Swedish dies and 5 bronze plungers. *Tools not included* -
Out of stock
Newfoundland ring blank designed specifically to be made into a ring. Designed from the Newfoundland 50 cent pieces, this ring blank has a 1/2" hole and is ready to be folded and made into a ring! Similar is size and shape of a United States half dollar, these make great rings for both men and women. Best if purchased with other items to combine shipping. NOTE: These are made from brass so it will discolor your finger NOTE: Ring not included -
A set of brass plungers to replace lost or damaged (beyond repair) plungers for the dollar and half dollar Swede dies. These are the best quality available being hardened bronze, engraved witness lines and being hand lapped. These are not just mass produced but rather each one is finished by hand by a skilled craftsman or woman here is the USA. The plungers being numbered from the largest to the smallest with the largest starting with #1, #2, #3, #4, and #5. It is o.k. for the plungers to have small dings and scratches when they become well used. If need be, you can always lap the surfaces using a piece of 200 grit sand paper. NOTE: This is the full set brass plungers. For additional information you can view a training video here: https://www.youtube.com/watch?v=W7gZxUKNr1g And also get detailed step by step instructions from my training manual available here: https://jasons.works/product/coin-ring-tools-training-manual/ *A special thank you to Mikael Möller, Robert Gibb (BFG Coin Rings), Bob, Russ, Troy, Mike Henry, Adam McKinney, Skyler Jenkins (Coin Rings by the Mint), Rocky Workman, Joshua Janes and countless others on Coin Ring Crafters on Facebook. You all made this possible! :) *COINS AND RINGS NOT INCLUDED* -
Pipe thread sealant tape for the Swedish Wrap. A total of ten rolls, each is 1/2" and 260" long. Thickness is .0028" There's better prices at your local hardware store, wally world, and online so be sure to shop around. I just wanted to offer an easy place to get some. *COINS AND RINGS NOT INCLUDED* -
(Note: The Auto punches will not work in the classic self centering punch) What you will receive: - Top and bottom Auto Punch housing. - One punch and die. Size of your choice. Select available sizes. - One protective plastic washer to protect the top housing during transport. - FREE PDF Training Manual "How To Make Coin Rings" (Swedish Wrap Technique) - FREE Excel Engine Calculator For Alloying Your Coin Silver Scrap Into Sterling Silver Watch an in depth video about the punch here: https://www.youtube.com/watch?v=GIkQy1H6MiI -
A set of brass plungers to replace lost or damaged (beyond repair) plungers for the dollar and half dollar Swede dies. These are the best quality available being hardened bronze, engraved witness lines and being hand lapped. These are not just mass produced but rather each one is finished by hand by a skilled craftsman or woman here is the USA. The plungers being numbered from the largest to the smallest with the largest starting with #1, #2, #3, #4, and #5. It is o.k. for the plungers to have small dings and scratches when they become well used. If need be, you can always lap the surfaces using a piece of 200 grit sand paper. NOTE: This is the full set brass plungers. *A special thank you to Mikael Möller, Robert Gibb (BFG Coin RIngs), Bob, Russ, Troy, Mike Henry, Adam McKinney, Skyler Jenkins (Coin Rings by the Mint), Rocky Workman, Joshua Janes and countless others on Coin Ring Crafters on Facebook. You all made this possible! :) *COINS AND RINGS NOT INCLUDED* -
This is a double sided reduction die as described in my manual with .7" and .8" openings at 25 degrees for the optimal fat tire look. The faces are at a special 25 degree, allowing for the detail on the outside of the coin ring to be better protected while reducing during the final sizing. This die is specifically used to get the smallest sizes possible on the smaller coins during the final stage of sizing. This die is to be used in conjunction with the other dies available and not by itself alone. You can achieve more of the "fat tire" look by using this die last. Coin sizes that can be used are the quarter, nickle and penny. * NOTE * This die should be used after the initial reducing has been done from the other dies in the set, and not by itself alone. This die will help your coin ring to achieve more of the rounded edge look (Fat Tire). *The coins pictured are not included* Tutorial Video: https://www.youtube.com/watch?v=lCwPbu1lGLY NOTE: A detailed description of the coin ring making process can be found in "How to Make Coin Rings" training manual found here: https://www.etsy.com/listing/170473451/training-manual-on-how-to-make-double? -
By popular demand, now you can store your folding/reduction dies to organize your workspace. Made from high-quality red oak, this tool holder will hold up to 11 reduction dies for easy access while making your coin rings, including the 1.7 x 1.8 @17 degree BIG boy die. * A recent review: "Excellent tray holds all my folding dies! Finished with what appears to be a light varnish to protect the surface while retaining the wood's natural color. The inside of each recess is bare. I might add a little clear coat or varnish in them, but I'm undecided on that as of now. If they were varnished I think the dies may clank around in each hole so maybe bare wood is the better option. I also got the Coin Ring Tool Holder which has the same finish as this. Excellent quality wood with no imperfections or cracks!" Angus MacGyver on Apr 25, 2016 5 out of 5 stars *Tools not included* -
Big savings when you buy kits! You also receive a FREE PDF Training Manual & Excel Engine Calculator with your order. (Note: The Auto punches will not work in the classic self centering punch) What you will receive: - Top and bottom Auto Punch housing. - Six punches and dies. Size of your choice. Select available sizes. - One protective plastic washer to protect the top housing during transport. – PDF Training Manual “How To Make Coin Rings” (Swedish Wrap Technique) – Excel Engine Calculator For Alloying Your Coin Silver Scrap Into Sterling Silver Watch an in depth video about the punch here: https://www.youtube.com/watch?v=GIkQy1H6MiI -
Out of stock
Ukrainian replica coin ring blank designed specifically to be made into rings. Designed from the Ukrainian 5 hryvnia, this ring blank has a 1/2" hole and is ready to be folded and made into a ring! Similar is size and shape of a United States half dollar, these make great rings for both men and women. Best if purchased with other items to combine shipping. NOTE: These are made from brass so it will discolor your finger NOTE: Ring not included -
NEW STABILIZING TOOLS! Replaces the delrin balls and stops coins from slipping in reduction dies when folding when using a ring stretcher reducer! *The full set is recommended. This cone is intended to replace a damaged or lost cone from the set. This is the stabilizer folding cone used to fold coins when using a ring stretcher/reducer machine with reduction dies. Use this cone to assist in folding half dollar, dollar, and American Silver Eagle sized coins. This is the first cone to use when beginning to fold a half dollar sized coin. These stabilizing cones are designed to replace the Delrin Folding Balls when using a ring stretcher/reducer machine to fold your coins. They use the same principal as the balls with added benefits. These cones will stabilize the coin in reduction dies, therefore not requiring a special stabilizing die for each type of coin. Just set the coin level in the universal reduction die, insert your folding cone and press the coin down through the hole. -
A single brass plunger to replace a lost or damaged (beyond repair) plunger. These are the best quality available being hardened bronze, engraved witness lines and being hand lapped. These are not just mass produced but rather each one is finished by hand by a skilled craftsman or woman here is the USA. I f you need multiple plungers, you can add them separately to your cart. For additional information you can view a training video here: https://www.youtube.com/watch?v=W7gZxUKNr1g And also get detailed step by step instructions from my training manual available here: https://jasons.works/product/coin-ring-tools-training-manual/ -
This is a full set of the universal double sided folding and reducing dies ranging from .7" to 1.6" openings at 17 degrees for optimal folding and reducing. These dies can be used in conjunction with the stabilizer folding cones and mandrels to fold U.S. dime to Silver Eagle sized coins leaving no mark on the inside of the coin. This die can also be used to fold and reduce similar sized coins for final sizing of coin rings. These dies can be used in conjunction with each other to pretty much fold and reduce all coins :) *The coins pictured are not included* Copy and paste this address into your internet browser address bar to see a youtube video using a die: https://www.youtube.com/watch?v=lCwPbu1lGLY NOTE: A detailed description of the coin ring making process can be found in "How to Make Coin Rings" training manual found here: https://jasons.works/product/coin-ring-tools-training-manual/ -
The coin ring technique called the Swedish Wrap, (created by Mikael Möller from Sweden) is now available! *Now you can make the smallest rings form the biggest coins! This kit comes with one 2" hardened stainless steel Swedish wrap die, 3 hardened bronze plungers, and FREE 2 rolls of pipe tape, and a Jason's Works Sticker. These dies are designed to be the most efficient Swedish wrap dies available. -
Choose the size punch and die you want for your classic self centering Jason's Works punch housing. Ideal to grow your punch kit or replace a worn or damaged punch. The punch and dies are made from hardened tool steel for long lasting punching. You can resharpen your punches for ultimate performance. Available sizes are: - 1/4" (bushing die) - 3/8" (bushing die) - 7/16" (bushing die) - 1/2" (bushing die) - 3/4" (washer plate die) *NOTE: The punch housing and spacers are not included. *Here is a video showing how to use the coin punch: https://www.youtube.com/watch?v=D4Fcjl6uWAIj NOTE: Here is a video showing how to use the washerplate type dies for the 5/8" ad 3/4" punches and the mega stretcher: https://www.youtube.com/watch?v=CQMNmlV-PRA NOTE: You can use either side of the washer platedie in the punch housing. -
Buy a kit and save! Also includes a PDF training manual & Excel Engine Calculator. (Note: The Auto punches will not work in the classic self centering punch) What you will receive: - Top and bottom Auto Punch housing. - Five punches and dies. Size of your choice. Select available sizes. - One protective plastic washer to protect the top housing during transport. – FREE PDF Training Manual “How To Make Coin Rings” (Swedish Wrap Technique) – FREE Excel Engine Calculator For Alloying Your Coin Silver Scrap Into Sterling Silver Watch an in depth video about the punch here: https://www.youtube.com/watch?v=GIkQy1H6MiI -
Order the size spacer you need in the drop-down menu below. For multiple coin ring spacers, please add each one you need to your shopping cart separately. Options include:- Angel Isle of Man
- Silver Eagle
- Morgan Dollar
- U.S. Presidential dollar, Susan B, and Sacagawea
- U.S. Half dollar
- U.S. Quarter
- U.S. Nickel
- U.S. Dime (this spacer includes a top plate to hold down your dime in the punch housing)
These spacers are to be used in conjunction with the self centering coin punch found here: https://jasons.works/product/classic-self-centering-coin-ring-punch-kit-die-set-one-punch-spacer-your-choice/ -
The coin ring technique called the Swedish Wrap, (created by Mikael Möller from Sweden) is now available! This kit comes with one hardened stainless steel Swedish wrap die, 3 hardened bronze plungers, and one free roll of pipe tape, and a Jason's Works Sticker. These dies are designed to be the most efficient Swedish wrap dies available. The idea is to use the bronze plungers to press the ring down (reeded side up and wrapped in pipe tape). These new taller style of bronze plungers are designed not to bottom out inside the die. The shortest ones is used first, then the medium sized and finally the tallest one to extrude the coin ring. For additional information you can view a training video here: https://www.youtube.com/watch?v=W7gZxUKNr1g And also get detailed step by step instructions from my training manual availabe here: https://www.etsy.com/listing/170473451/new-swedish-wrap-technique-edition-42?ref=shop_home_active_8 The smaller sized rings can be incorporated into bracelet, necklaces, pendants, earrings, even ear gauges! -
The coin ring technique called the Swedish Wrap, (created by Mikael Möller from Sweden) is now available! *Now you can make the smallest rings from the biggest coins! These dies are designed to be the most efficient Swedish wrap dies available. Choose the size you would like to get. Multiple dies can be ordered by placing separate with orders in your cart. For additional information you can view a training video here: https://www.youtube.com/watch?v=W7gZxUKNr1g https://www.youtube.com/watch?v=fHWGStPCL6Q And also get detailed step by step instructions from my training manual availabe here: https://www.youtube.com/watch?v=fHWGStPCL6Q The smaller sized rings can be incorporated into bracelets, necklaces, pendants, earrings, even ear gauges! *COINS AND RINGS NOT INCLUDED* -
This is a double sided folding and reducing die with .7" and .8" openings at 17 degrees for optimal folding and reducing. This die can be used in conjunction with the stabilizer folding cones and mandrels to fold U.S. penny and dime sized coins leaving no mark on the inside of the coin. This die can also be used to reduce similar sized coins for final sizing of coin rings. *The coins pictured are not included* Copy and paste this address into your internet browser address bar to see a youtube video using a die: https://www.youtube.com/watch?v=lCwPbu1lGLY NOTE: A detailed description of the coin ring making process can be found in "How to Make Coin Rings" training manual found here: https://www.etsy.com/listing/170473451/training-manual-on-how-to-make-double?
The Highest Quality USA Coin Ring Tools Guaranteed
If you have any questions, feel free to reach out and email me at info@jasons.works. I look forward to making a ring for you, or even better, helping you learn how to make them yourself!
Subscribe to our newsletter
Sign Up to our newsletter to get latest updates!
Jason Stinchfield, Jason’s Works
I am proud to provide the world with the highest quality coin ring resources available. From training to tools, as well as custom made-to-order rings, I believe this is the best website on coin rings on the net. Have fun looking around, and don’t forget to subscribe to my YouTube channel to learn tips and tricks, and even watch me make a ring. Also find me at RioGrande.com, Instagram (most active ;), Facebook, and Pinterest. Be sure to browse the coin rings available as well; each ring is made by yours truly, from coin selection to dropping it in the mail.
PEOPLE I SUPPORT
Coin Ring Makers
– Adam McKinney
– Skyler Jenkins
– Joshua Janes
– Matt-MacGyver Bennett
– Robert Gibb
– Rocky Workman
– Augusta Simmons
– Gene Obrien
– Coin Ring Crafters Facebook group
– Nick Crutchfield
Tool Makers
– Rio Grande
– Skip King
– Ross coin ring tools
Copyright © 2021 Jason’s Works. All Rights Reserved | Policies, Privacy, & Terms | Site by ZOOGABOOG!